nvrl
b8d04d1936
The producer-feedback round: stable note tracking, the NOTE pitch source with Key lock and Follow bends, unsure-means-neutral fallbacks, Anvil's Enhance mode, MAIN and ADVANCED pages, Ballast on Grid by default, and Crucible's sure-note slice names with a song key. Adds docs/pitch.md for the shared pitch source, updates every changed plugin's README and changelog, the release table, the editor previews, the website bullets, and the status in docs/ideas.md.
4.2 KiB
Braze
Braze makes a reese's movement play in time. Current version 0.2.0.
Two layers detuned against each other beat: harmonic k of a note at f0 swells and fades k·f0·(r − 1) times per second, where r is the detune ratio. With a fixed detune that rate changes with every note, so the movement of a reese never lines up with the track. Braze adds a detuned copy of the bass and sets its detune on every note so that the beating follows the tempo.
Install on Windows
Copy Braze.clap into C:\Program Files\Common Files\CLAP\. In FL Studio 2024.1
or newer, open Options → Manage plugins, enable Verify plugins, and Find installed
plugins. Load Braze in the mixer slot of the bass. Keep the font license with
redistributed packages.
Work with it
The editor opens on the MAIN page with Rate, harmonic, Depth, Low cut, Width and Output. The ADVANCED switch in the header adds Phase, Gate and Snap.
- Put Braze on a single bass layer: a plain saw, or a reese whose own detune you have turned down.
- Pick Rate: the note value one beat lasts. 1/8 at 140 BPM is 4.67 beats per second.
- Pick the harmonic that should beat at Rate. Harmonic n beats n/harmonic times as fast, so all of them beat on the grid: with harmonic 4 at 1/8, harmonic 2 beats in quarters, harmonic 8 in sixteenths, harmonic 3 in quarter triplets.
- Set Depth. At 100 % the beating goes down to full nulls; 50–70 % keeps the note present.
- On the ADVANCED page, use Phase to move where the beat peaks. At 0° all harmonics peak together on every beat of the chosen harmonic's cycle.
The display shows one bar: a row per harmonic with the level it gets from the beating, the grid at Rate, and the playhead.
Other controls:
- Low cut removes the copy below a frequency, so the sub does not beat. The sub keeps its level. Harmonics under the cut show cut in the display. Under 20 Hz the cut is off. If the chosen harmonic is under the cut on a note, it does not beat: the note panel says so; pick a higher harmonic.
- Width moves the right channel's beat against the left, up to half a cycle. At 100 % one side peaks while the other nulls. Check the mono sum.
- Gate is the input level that counts as a note.
- Snap to semitone rounds the detected pitch. Leave it off on detuned or bent notes: the copy jumps by one period of the pitch in use.
Pitch source
Pitch from in the header chooses where the note comes from: AUDIO detects it, MIDI follows MIDI notes sent to Braze, and NOTE uses a note you set. For heavy FM, formant or noise basses, NOTE with the drop's root is the safest choice. Key lock and Follow bends tune the detection. While detection is unsure of the note, Braze keeps the detune of the last sure note and the readout shows ?. See Pitch source.
How the detune is made
The copy is the bass read from a delay line. Its delay falls by one period of the note per beat cycle of the chosen harmonic, which tunes the copy up by exactly r = 1 + B/(k·f0) (B: beats per second, k: the chosen harmonic). When it has fallen a whole period, it jumps back by one period: on a steady note both read positions hold the same waveform, so the jump is crossfaded over 6 ms without a seam. At a beat peak the copy lines up with the bass sample for sample.
The low detune that low notes need is large: harmonic 1 at 1/8 and 140 BPM on F1 (43.7 Hz) is r = 1.107, about 1.8 semitones. Higher harmonics need less: harmonic 4 asks for about 45 cents on F1.
Timing and limits
Detection uses about 67 ms of lookahead, reported to the host for delay compensation. Pitch range is 30–500 Hz, one voice. The beat position comes from the host while it plays, shifted by the lookahead so the beat stays on the timeline. When the host is stopped, the beat runs on freely at the last tempo.
Noise, chords and the attack of a note are not periodic, so the copy's jumps are heard there as a short blur. Before the first note, the copy assumes 55 Hz.
Braze changes the waveform in time, so pitch detection after it can be less sure: put tracked plugins before Braze, or use MIDI or NOTE. See Signal chain.