One note tracker reads the input and Lathe, Temper and Knurl follow it as
modules, in any of six orders, each on or off. Every module gets the
tracker's events delayed by the latency of the modules in front of it.
- One module alone matches its standalone plugin sample for sample in
every order.
- With Knurl's sub-octave pattern in front, Lathe in Forge follows the
played note; a standalone Lathe after Knurl reads it an octave low.
- About 72 ms latency against about 206 ms for the three in a row.
The module pages reuse the standalone editors. Register Forge in the
catalog, CI, README, docs and website, and drop the built Ballast from
the site's idea list.
Ballast gives every part of a bassline one gain that brings it to the target
loudness, with no compression inside a part. Parts start at note starts,
detected from the audio or taken from MIDI, or on the host's beat grid, so a
patch change on the same note counts too.
- Loudness is K-weighted over each part's first 100 ms, in 10 ms blocks with
a relative gate, and every part is weighted from rest so the last part does
not ring into it.
- The audio path is delayed by the tracker's lookahead, the window and a
5 ms glide, so each gain is in place on its part's first sample.
- Learn takes the next part's loudness as the target. Amount, Range, Measure
from (leave the sub out), Gate, Output, Bypass.
- Editor shows the last 32 parts in and out, the target, and the spread of
the last 16 parts.
- Registered in the catalog, workflows, editor-check, README, chain and
development docs, and the website copy.
Quench splits the signal with a Linkwitz-Riley crossover and lets the sub
pass unclipped. The top is clipped symmetrically at the ceiling minus the
sub's held peak, so it does not pump at the sub's rate and the sum stays
under the ceiling. What the clip removes is high-passed at the split, so its
products stay out of the low band. Two correction passes and an oversampled
hard clip hold the ceiling; a safety clip catches the downsampler's ringing.
- Controls: Drive, Ceiling, Split, Hold, Soft, Bypass.
- Listen to Quench, a plain clipper at the same settings, or the delta.
- Editor meter compares how much the low band changed for Quench and for a
plain clip, with a scope of the output, the sub and the top's room.
- Measured: sub level +0.04 dB against -2.2 dB for a plain clip, low-band
products -35 dB against -16 dB, at 0.5-1.2 dB less RMS.
- Registered in the catalog, workflows, editor-check, README, chain and
development docs, and the website copy.
Anvil gets a sidechain input named Kick. With Kick lock on, kicks are
found on the undelayed sidechain, so with the lookahead each hit ducks
the sub (Duck, Release) when the delayed kick plays and restarts the sub
at Phase, shifted by Offset (-30 to +30 ms, also before the kick).
The Audition steps the offset from -30 to +30 ms, 4 kicks each, and
measures how kick and sub sum below 150 Hz after each hit; Keep takes the
offset heard. On a 55 Hz kick burst against a 55 Hz sub the sum peaks at
0 ms (+2.4 dB) and nearly again one period away (+/-20 ms), so the bars
check the choice by ear rather than make it.
Adds a detuned copy of the bass whose beating stays on the tempo grid on
every note. The chosen harmonic k beats once per Rate note value, and
harmonic n beats n/k times as fast, so every harmonic is on the grid.
- The copy is read from a delay line whose delay falls one period of the
tracked note per beat cycle (r = 1 + B/(k f0)) and jumps back exactly
one period, crossfaded over 6 ms. On a periodic note the jump has no
seam: the output matches the ideal sum within 0.003 on harmonics 1-4.
- The delay follows the host's beat position, shifted by the lookahead,
so beat peaks land on the grid; free-running when stopped.
- Low cut: LR4 high-pass on the copy, the bass split by the same
crossover, so the sub does not beat and keeps its level.
- Depth, Width, Phase, Gate, Output, Snap, Bypass. Pitch from audio
(about 67 ms lookahead) or MIDI.
- Editor: one bar of the beat per harmonic with the grid and a playhead.
- Catalog, workflows, editor-check, docs, signal chain and site copy.
Upward and downward compression in four bands whose edges are harmonic
numbers of the tracked note (default 1, 2-4, 5-16, 17 and up), so the
same setting squashes the same harmonics on every note. A fixed-band
OTT puts harmonic 2 of F1 and of C2 in different bands.
- Three Linkwitz-Riley splits at sqrt(k(k+1)) x f0 with allpass
compensation; at Depth 0 the bands sum within 0.05 dB.
- Band level is the RMS over one period of the note, so heavy settings
do not ripple at f0: a 40 Hz sine at Drive +12 dB, Time 10 % gets no
harmonics above -110 dB.
- At Depth 100 % on a saw, harmonics 1-12 change by the same amount on
F1, C2 and G2 (within 0.2 dB).
- Depth, Drive (on the detector only), Upward, Downward, Time, a gain
per band; edges Low 1-8, Mid 2-16, High 3-48 with four splits.
- Pitch from audio with about 67 ms lookahead, or from MIDI.
- Editor: harmonic ruler with draggable edges, level and gain per band.
- Catalog, workflows, editor-check, docs, signal chain and site copy.
docs/chain.md gives the plugin order for a bass track and the bus, the
latency each plugin adds, and the measured octave error of downstream
note trackers after Knurl: from C2 up the tracker reads an octave low
about 85 % of the time, and timing jitter adds 5-25 false note starts
per second. Knurl and Anvil guides point there and recommend MIDI as
the pitch source after Knurl.
docs/ideas.md gains the production-flow audit, next steps for every
released plugin, new ideas (Forge, Planish, Quench, Scribe, Bevel,
Peen) and a build order.
nvrl