feat(ballast): add Ballast switch-up leveller
Ballast gives every part of a bassline one gain that brings it to the target loudness, with no compression inside a part. Parts start at note starts, detected from the audio or taken from MIDI, or on the host's beat grid, so a patch change on the same note counts too. - Loudness is K-weighted over each part's first 100 ms, in 10 ms blocks with a relative gate, and every part is weighted from rest so the last part does not ring into it. - The audio path is delayed by the tracker's lookahead, the window and a 5 ms glide, so each gain is in place on its part's first sample. - Learn takes the next part's loudness as the target. Amount, Range, Measure from (leave the sub out), Gate, Output, Bypass. - Editor shows the last 32 parts in and out, the target, and the spread of the last 16 parts. - Registered in the catalog, workflows, editor-check, README, chain and development docs, and the website copy.
This commit is contained in:
1 parent
d77b88c7a9
commit
d93dd942a8
28 files changed
+4716
-21
No files matched your search
+10
-5
@@ -1,13 +1,13 @@
|
||||
# Signal chain
|
||||
|
||||
The order of the Bass Foundry plugins in a chain matters. Anvil, Lathe, Temper,
|
||||
Knurl, Planish and Braze each detect the pitch from the audio they receive. If a plugin earlier
|
||||
Knurl, Planish, Braze and Ballast each detect the pitch from the audio they receive. If a plugin earlier
|
||||
in the chain changes the audio, the pitch detection after it can go wrong.
|
||||
|
||||
## Recommended order
|
||||
|
||||
```text
|
||||
bass track: synth → Lathe → Temper → Planish → Braze → Knurl → Patina → Weld
|
||||
bass track: synth → Lathe → Temper → Planish → Braze → Knurl → Patina → Ballast → Weld
|
||||
bass bus: Anvil → (bus compression) → Quench → Crucible
|
||||
master: … → Quench (last, or before a true-peak limiter)
|
||||
```
|
||||
@@ -23,7 +23,12 @@ master: … → Quench (last, or before a true-peak limiter)
|
||||
it reads Loose, move Braze to the bus after Anvil, with Low cut at or above
|
||||
Anvil's Split. There it reads the pitch from Anvil's clean sub, and the sub
|
||||
stays out of the beating.
|
||||
- **Knurl last among the tracked plugins.** See below.
|
||||
- **Ballast after the sound design.** It levels what the patch finally sounds
|
||||
like, so it comes after the distortion, OTT and Patina. It finds note starts
|
||||
like the other tracked plugins: after Knurl, use MIDI or Grid. Weld and Anvil
|
||||
come after it. On the bus with Anvil, set Measure from to Anvil's Split.
|
||||
- **Knurl last among the pitch-tracked plugins.** See below. Ballast only
|
||||
needs note starts; after Knurl, run it from MIDI or the grid.
|
||||
- **Patina after the tracked plugins.** It does not detect pitch, so the order
|
||||
does not change its result.
|
||||
- **Weld after every plugin with latency on its track.** Weld can delay its own
|
||||
@@ -58,8 +63,8 @@ and route the bass's MIDI notes to it.
|
||||
## Latency
|
||||
|
||||
Each tracked plugin adds its own lookahead: Anvil 80 ms, Lathe, Temper,
|
||||
Planish and Braze about 67 ms, Knurl about 71 ms, Patina about 45 ms, Quench
|
||||
under 1 ms. A full chain is
|
||||
Planish and Braze about 67 ms, Knurl about 71 ms, Patina about 45 ms, Ballast
|
||||
about 172 ms, Quench under 1 ms. A full chain is
|
||||
about 400 ms. FL
|
||||
Studio compensates this for playback and rendering, but playing a MIDI keyboard
|
||||
through the full chain is not practical. Write with a shorter chain and add the
|
||||
|
||||
Reference in new issue
Block a user